ASTM D Standard Test Methods for Carbon Black-Heating Loss. standard by ASTM International, 06/01/ View all product details. Most Recent. ASTM D – 95(). Standard Test Methods for Carbon Black—Heating Loss. This standard is a part of ASTM Book of Standards Volume Find the most up-to-date version of ASTM D at Engineering
|Published (Last):||28 September 2013|
|PDF File Size:||9.21 Mb|
|ePub File Size:||11.79 Mb|
|Price:||Free* [*Free Regsitration Required]|
It x1509 the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Historical Version s – view previous versions of standard. As the voice of the U. This standard asm been approved for use by agencies of the Department of Defense. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.
Your Alert Profile lists the documents that will be monitored. Place the bottle and stopper in the desiccator and allow to cool 3. A superscript epsilon indicates an editorial change since the last revision or reapproval. Users of this standard are d15099 advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This heating loss relative humidity, ambient temperature, and time to which the consists primarily of moisture, but other volatile materials may material is exposed.
NOTE 1—Keep the stopper on the weighing bottle when transferring to and from the desiccator to prevent loss of carbon black due to air currents.
It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Asmt pricing is determined by: However, these materials were not included in the precision studies and therefore, the precision statements contained in this standard may not be valid for these materials.
The observed difference in mass is the nearest 0.
ASTM D – 18 – Standard Test Methods for Carbon Black—Heating Loss
If the document is revised or amended, you will be notified by email. The f1509 given in parentheses are for information only. Proceed to Checkout Continue Shopping. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. Link to Active This link will always route to the current Active version of the standard. Calculation some appropriate action be taken.
Such a decision dictates that This heating loss consists primarily of moisture, but other r1509 materials may also be lost. It is the in diameter, equipped with a ground-glass stopper.
ASTM-D | Standard Test Methods for Carbon Black&#x;Heating Loss | Document Center, Inc.
S r within-laboratory standard deviation, r repeatability in measurement unitsr repeatability in relative percentSR between-laboratory standard deviation, R reproducibility in measurement unitsand R reproducibility in relative percent. The values given in parentheses are for information only. Sampling rejection testing of any group of materials without documen- Last previous edition D — 93a. Need more than one copy? Refer to Practice D for NOTE 2—An indirect heating source is preferred due to the ability of a terminology and other statistical details.
Normas Aplicáveis aos Negros de Carbono
Two less than 1 mg over 30 s the test portion is considered dry and single test results or determinations that differ by more than the percent mass loss should be recorded to the nearest 0. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. This standard is not included in any packages.
This standard does not purport to address all of the safety concerns, if any, associated with its use. These test methods are not applicable to treated carbon zstm that contain added volatile materials, if moisture loss is to be measured.
Eight laboratories tested three carbon blacks Ma- Procedure terials A, B, and C twice on each of two different days. The amount of moisture absorbed is related to the surface area of the black and to the relative humidity, ambient temperature, and time to which the material is exposed. Both before starting the test. Individual reprints single or multiple copies of this standard may be astj by contacting ASTM at the above address or at phonefaxor service e-mail ; or through the ASTM website.
Precision and Bias It is the responsibility of the user of this standard to establish d1590 safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. A mass of weighing bottle and stopper, g, B mass of weighing bottle, stopper, and d109 before This heating loss consists primarily of moisture, c1509 other volatile materials may also be lost.
In addition to determining the heating loss primarily moisture content of carbon black, these drying conditions are used to prepare samples prior to performing other carbon black tests. However, these materials were not included in the precision studies and therefore, the precision statements contained in this standard may not be valid for these materials. These test methods are not applicable to treated D11509 A—Convection—Gravity Oven Method carbon blacks that contain added volatile materials, if moisture loss is to be measured.
Reference values do not exist for this test heating, g. The amount of moisture 1. Acceptable difference values were not measured. The precision parameters should not be used for acceptance or Historical Version s – view previous versions of standard Translated Version s: