This standard is issued under the fixed designation D; the number 1 This test method is under the jurisdiction of ASTM Committee D04 on Road. RELEVANT DOCUMENTS. ASTM D Standard Test Method for Flat Particles, Elongated Particles, or Flat and. Elongated Particles in Coarse Aggregate. The standard flat and elongated particles in coarse aggregate test is: ASTM D Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse.
|Published (Last):||4 April 2010|
|PDF File Size:||6.21 Mb|
|ePub File Size:||10.24 Mb|
|Price:||Free* [*Free Regsitration Required]|
Flat and elongated particle pavementinteractive. GMC All rights reserved. Flat and elongated particles Clay Content. CE Construction Materials Engineering: If the particle does not meet either classification of Flat or. A number in parentheses indies the dd4791 of last.
specification of flat and elongated particles
Mining Equipment Sales Companies. Percentage of Fractured Particles shall be determined on the aggregate blend. The user should set the larger opening of the Caliper equal. The fine aggregate shall be limestone, dolomite, crushed gravel, steel furnace The excess heaped aggregate is struck of using the included bar, the mass is measured, s4791 the void content is computed.
Except where noted elsewhere in the Contract Documents, blending to improve the physical requirements shall not be permitted, except to increase the percentage of crushed particles or decrease the percentage of flat and elongated particles.
VMA the volume of intergranular void space between the aggregate particles of a compacted paving mixture that includes the air voids and the effective binder content expressed as a …. The user should carefully review the ASTM procedure before testing.
News and Downloads
Method A is a reflection of the asm procedure as developed prior to Superpave and is intended for all non-Superpave applications. Gauge satm seven labeled slots for rapid hand trying of particles from each of the seven sieve cuts. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Aggregate base course shall be accepted for density on a lot basis. Proportional Caliper for measuring flat and elongated particles Taking for r4791 the current methodology for measuring flat and elongated particles, as per ASTM specification ….
For Classification of Flat Particle Testing:. Referenced Documents purchase separately The documents astn below are referenced within the subject standard but are not provided as part x the standard.
These instructions are a general guide for operation of this. This test method provides a means for checking compliance with specifiions that limit such particles or to determine the relative shape characteristics of coarse aggregates.
BoxAsm Center, Ohio The test method covers the determination of the percentages of flat particles, elongated particles, or flat and …. The granular base is typically dense graded, with the amount of fines limited to promote drainage.
Testing equipment for the construction industry – CONTROLS
The complete procedure for determination of relative shape characteristics of coarse aggregates using the Four- Station Caliper is described in ASTM D Consult the current edition of ASTM for procedure in its entirety and equipment specification details. Cubical particles are desirable, with a limited amount of flat or thin and elongated particles.
Scratch Hardness Tester— H Scratch Hardness Tester determines quantity of soft particles in coarse aggregates on basis of scratch hardness. Flat and Elongated Particles shall be determined on the aggregate blend. Method B is a comparison of the maximum particle dimension to the minimum particle dimension and is intended for use with Superpave specifications.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Use GDT to analyze these materials. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. For Classification of Elongated Particle Testing:.
Furnished with one extra brass scratch rod. Construct a base course, a surface course, a level-up course, or any combination of Link to Active This link will always route to the current Active version of the standard. The standard flat and elongated particles in coarse aggregate test is: A flat and elongated piece is defined as one having a ratio of length to thickne ss greater than five.
The user dd4791 set the larger opening of the Caliper. x4791
If the width of the same particle can. Effects of flat and elongated particles upon properties of Coarse aggregate shall be aggregate retained on the No. Conduct this pr aztm according to ND D Two procedures, Method A and Method B, are presented in this standard. Proportional Calipers Device for Aggregates Testing Units are constructed of durable plated steel, precision tooled for accuracy.
ASTM D4791 – 10
The particles shape of course aggregates influences the properties of some construction materials and may affect their placement and consolidation. Provide coarse aggregate free of coatings of clay and silt. The SI units in parentheses are for information purposes only.
For determining flakiness index. Flat-and-elongated particles are considered to be undesirable in HMA because they have a tendency to break or degrade during the construction process and under applied traffic. Individual particles of aggregate of specific sieve sizes are.
The mass of all elongated particles failing to pass between pins as percent of aastm sample is the elongation index.