PDF Download


ASTM D Standard Test Method for Dissipation Factor (or Power Factor) and Relative Permittivity (Dielectric Constant) of Electrical Insulating Liquids. Find the most up-to-date version of ASTM D at Engineering We perform testing by ASTM D on electrical insulating liquids used in cables, transformers, oil circuit breakers, and other electrical apparatus.

Author: Akinotaur Shaktimi
Country: Puerto Rico
Language: English (Spanish)
Genre: Sex
Published (Last): 22 May 2007
Pages: 446
PDF File Size: 15.10 Mb
ePub File Size: 14.70 Mb
ISBN: 756-5-92149-995-1
Downloads: 54216
Price: Free* [*Free Regsitration Required]
Uploader: Felabar

When used as the dielectric in a capacitor, it is desirable to have a higher value of relative permittivity so the physical size of the capacitor may be as small as possible.

Internal standard capacitor electrode type capacitor,with electrode spacing 2mm. Precision and Bias If the difference in the measurements of the two test specimens is equal to d24 less than 0. Use a shielded wire or coaxial cable for connecting the guard and measuring electrodes to the bridge.

ASTM D924 Large-Screen Auto Washing Insulating Oil Dielectric Loss Tester

For the first use, a low value of relative permittivity is often desirable in order to have the capacitance be as small as possible, consistent with acceptable chemical and heat transfer properties. Transformer tester, High voltage generatorRelay test kitPower quality analyzerinsulating oil testerHigh voltage tester, Insulation tester, Earth resistance tester and so on.

Consult such procedures before samples are taken. Plated surfaces that may be satisfactory for testing liquids having low acidity and for short periods of time are gold, platinum, nickel, chromium over nickel, or rhodium. We have our own manufacturing factory,pls see the below certificate,we are the direct supplier. If the difference between the third measurement and either the rst or second is not within 0. Record data as soon as the test temperature is reached.

Enter between 20 to 4, characters. Use a perforated ceramic plate or disk to insulate the test cell from the metal ooring of the oven if the ooring is not insulated from the oven. Current edition approved Nov. As a precaution against this eventuality, use a suitable stopper to plug this opening prior to starting the cleaning operation. Replace the inner electrode.


Typical questions asked about products Does this product support customization? Use these measurements in calculating the relative permittivity from the following equation: Remove the inner electrode and hold it suspended in air; then decant the rinsing liquid and immediately ll the cell from the remainder of the heated specimen.

If it is not feasible, the length of time the sample is exposed to atmospheric conditions must be kept to a minimum. Get Latest Price Min. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn. Contact Now Customized Request. It is essential, therefore, that the procedures outlined below be closely followed.

Cleaning Test Cell Mercury, or its vapor, may be hazardous to health and corrosive to materials. Some liquids, such as oils of petroleum origin, undergo changes when exposed to sunlight. Specic warnings are given in Huazheng Electric Manufacturing Baoding Co. However, an intermediate value of relative permittivity may sometimes be advantageous in achieving a better voltage distribution of ac electric fields between the liquid and solid insulating materials with which the liquid may be in series.

HS code is ; 2. Shipped in 15 days after payment.

Send your message to this supplier. Wooden box with foam inside, 3. D — 08 Standard Test Method for Dissipation Factor or Power Factor and Relative Permittivity Dielectric Constant of Electrical Insulating Liquids1 This standard is issued under the xed designation D ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of asm revision.


Where this applies, it is imperative that each laboratory evolves a good cleaning procedure for the cell used so that repeatable results can be obtained. A low dissipation factor or power factor indicates low ac dielectric losses.

Originally approved in as D — 47 T. In general, since the dissipation factor or power factor of insulating oils in good condition have decimal values below 0. Equipped with over-voltage, over-current and limit protections.

No fumigation,not influence the delivery; 4. Contact Supplier Start Order. Link to Active This link will asrm route to the astk Active version of the standard.

Caution should be taken when handling mercury and mercury containing products.

Due regard should be given to the precautions outlined in Section China hair loss China weight loss equipment China vacuum fat loss machine. Take care that the surfaces on which the component parts of the cell are placed in the oven are clean. Gold Member Since Insulating Oil Dielectric Loss Tester.

ASTM D液体绝缘材料介质损耗测试法_百度文库

On some instruments the cell must be in place before lling with specimen. Send This is not what you are looking for? Preparation of Specimen and Filling Test Cell Tests at higher stresses aztm desirable but shall not reach such values that electrical discharges across the cell insulating surfaces occur or that internal ionization of the specimen may be expected. We Do Our Best for You! Immediately return the lled cell to the test chamber d294 to a temperature above the desired test temperature and make the necessary electrical connections to the cell.

It is required, however, that the precision of the measurements meets the intended accuracy of this test method.