PDF Download

BC558C DATASHEET PDF

BCC datasheet, BCC pdf, BCC data sheet, datasheet, data sheet, pdf, Boca Semiconductor Corporation, 30 V, PNP silicon planar epitaxial transistor. BCC Transistor Datasheet pdf, BCC Equivalent. Parameters and Characteristics. BC Silicon PNP Transistor. Audio Amplifier, Switch. Features: D Suitable for AF-Driver Stages and Low Power Output Stages. Absolute Maximum Ratings.

Author: Akikree Taulkis
Country: Eritrea
Language: English (Spanish)
Genre: Marketing
Published (Last): 19 October 2014
Pages: 154
PDF File Size: 15.97 Mb
ePub File Size: 3.67 Mb
ISBN: 317-6-12979-679-5
Downloads: 76970
Price: Free* [*Free Regsitration Required]
Uploader: Goltijind

When uses as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae. It is used in switching and amplifier applications.

This high-density System-in-Package SiP integrates controller, power switches, and support components. A resistor is datasjeet added in series with base pin to limit the base current.

BC558 Datasheet, Equivalent, Cross Reference Search

What is Web Browser. For amplification applications, the transistor is biased such that it is partly on datashdet all input conditions. Submitted by admin on 26 March As discussed a transistor will act as an Open switch during Forward Bias and as a closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin. This is known as the biasing. A Transistors acts as an Amplifier when operating in Active Region.

Complete Technical Details can be found in the BC datasheet datasheef at the end of this page. When this transistor is fully biased then it can allow continues current of mA to flow across the collector and emitter. Arduino based GPS receiver. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV.

  CAMURATI-ENGELMANN DISEASE PDF

BC Transistor | BC Datasheet

Where an input signal of low voltage is amplified switched to high voltages t0 drive loads like speakers. For switching applications, transistor is biased so that it remains fully on if there is a signal at its base. Amplifier modules like Audio amplifiers, signal Amplifier etc.

SPI Module of Arduino. The value of this resistor RB can be calculated using below formulae. BC has a gain value of to ; this datashewt determines the amplification capacity of the transistor. The DC current gain varies in range to Choosing Motor For Robots. Also note that a PNP transistor is always used for high side switching, meaning the collector is connected to power and emitter to load that datxsheet to be switched.

In the absence of base signal, it gets completely off. The voltage divider is the commonly used biasing mode.

BCC Datasheet(PDF) – Rectron Semiconductor

Interface GPS with Arduino. BC is a general purpose PNP transistor. The transistor terminals require a fixed DC voltage to operate in the desired region of its characteristic curves.

  COMPUTER ARITHMETIC ALGORITHMS ISRAEL KOREN PDF

It datashheet amplify power, voltage and current at different configurations. It is also used as a complement for transistors BC to BC BC is used in common emitter configuration for amplifiers.

Virgin Galactic — Commercial Space Flight. TL — Programmable Reference Voltage.

BC is a PNP transistor hence the collector and emitter will be closed Forward biased when the base pin is held at ground and will be opened Reverse biased when a signal is provided to base pin. When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above.

BC558C Datasheet

In the below GIF you can notice the transistor being switched for a low voltage 1v audio signal. The BC because of this large gain value is normally used to as a audio amplifier. Skip to main content.

Choosing Battery for Robots.

The input signal at base is amplified and taken at the emitter. Interface SD Card with Arduino. Of the above types common emitter type which amplifies voltage is the popular and mostly used configuration.

BC as switch When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region datasyeet explained above.