Dome Camera Installation Manual Weatherproof and Indoor versions www. Contents Introduction. Menu System Manual. Page 4 of 1. THE DENNARD TYPE DOME CAMERA. The Dennard Dome Camera is a precision unit, offering a wide. The Dedicated Micros Camera has a number of features which can be selected by the System. Supervisor when the dome is installed. Any of these can be.
|Country:||Sao Tome and Principe|
|Published (Last):||27 August 2007|
|PDF File Size:||7.93 Mb|
|ePub File Size:||3.40 Mb|
|Price:||Free* [*Free Regsitration Required]|
Scan across the table to identify the values for the blue and yellow switches. Posted April 3, Arecont Vision Contera indoor dome series. This offers a range of features which are described below. Control Switches – Indoor Dennatd Remove and retain the four screws securing the shield to the head and lift off the shield. By pressing ‘print’ button you will print only current page.
Check the dome address switches are correctly set for the controller being used. Multicore cable with integral Co-ax Video b. Open the Technician Menu see Operation and Programming manual for details on accessing the menu. Hi, I am completely new to cctv, in fact I am installing a setup at my home, I am not a professional installer or anything like that so please forgive my lack of technical knowledge.
Always support dome with bond prior to mating connector B. Share this post Link to post Share on other sites.
DM with rx domes are delivered with the address switches set at Termination All Dedicated Micros domes are fitted with a termination switch, shown above.
Dedicated Micros Dennard 2060 Dome with 36x optical zoom
It’s a community-based project which helps to repair anything. Hanwha Techwin introduces four stainless-steel dome cameras to Wisenet X series. Fit the supplied safety bond E to an attachment point in the 200. Attach safety bond to a suitable secure position in the ceiling void. The mechanism needs to be removed from the denjard to enable this. Page 11 C into the keyhole slots on the base of the dome F enclosure. The Dedicated Micros Dennard dome is having its maximum optical zoom setting increased from 26x to 36x and its digital zoom setting improved from 4x to 12x.
Also, when I have tested the cameras successfully and come to install, I have purchased a reel of RG6 u co-azial cable as I have read I sennard get a better signal than the more common RG59, is that a good enough solution?
Always support dome with bond prior to mating connector B. Dedicated 0260 zooms in with Dennard Select the node address of the dome to be configured. If mounting onto masonry, insert 4x M6 rawlplugs into the wall until flush.
Got it, continue to print. Check the Input and Output voltage 2. Vandal resistant Additional info Advanced privacy patches, preset positions and tour facilities.
The weight dennqrd dome should be supported by bond ensuring no stress is placed on centre connector at any time. This operation should be carried out in an office type environment to avoid ingress of moist air. Dedicated Micros range extended to include a new indoor dome.
Don’t show me this message again. DM with rx domes are delivered with the address switches set at The external camera is weatherproof IP rated. Dome Mounting – Weatherproof Dome Lift the dome to the bracket flange ensuring head of screws pass through the keyhole slots.
Scan across the table to identify the values for the blue and yellow switches. Also, do I need to terminate the power debnard control twisted pairs that are also in the pigtail with the coax?
Dennaed link must be left on permanently.
Dedicated Mircros Dennard Installation manual |
Troubleshooting No joystick dead band recognized as joystick was off centre during powerup. For example using the 36x optical zoom on a standard UK car number plate can be viewed at full screen width up to 17m away from the camera versus 11m away with 18x camera, or 13m away 26x. To Frame the image from a Fixed attitude camera; You might be interested in these products. Already have an account? Fasten the dome to the mounting ring B using the provided 3 x No. Do not show this again.
Twist once located to secure, then tighten screw heads C to secure the dome enclosure to the mounting disk. Attach the mounting disc B to the ceiling in the chosen position and fix 4x M6x16 socket head cap screws supplied into the bushes C as shown below.
Fit the supplied safety bond E to an attachment point in the ceiling.