PDF Download

EN 10002-2 PDF

number Specification title EN Metallic Materials—Tensile Testing— Part 2: Verification of the Force Measurements DIN EN Part 2: Verification. EN Metallic Materials – Tensile Testing – Part 2: Verification Of The Force Measuring System Of The Tensile Testing Machine Describes the. Sep 25, Tensile testing of metallic materials —. Part 2: Verification of the force measuring system of the tensile testing machine. Licensed.

Author: Kira Kekree
Country: Mozambique
Language: English (Spanish)
Genre: Automotive
Published (Last): 6 December 2012
Pages: 452
PDF File Size: 3.82 Mb
ePub File Size: 19.81 Mb
ISBN: 673-6-56430-686-3
Downloads: 49132
Price: Free* [*Free Regsitration Required]
Uploader: Moogujinn

Metallic materials – Tensile testing – Part 2: Method for tensile testing of metals.

V exerted by the masses is noted. BS EN Tensile testing of metallic materials.

DXL (2 lbs) (10 x 10 x 2) (non-NTEP)

This page may contain references to products that are not available in your country. Tensile testing according to EN -1 is one of the basic mechanical tests to characterise the mechanical properties of metallic materials. Specimen shape A should be preferred. Metallic materials u Tensile testing u Part 1: If this is not possible, the alternative dimensions should be The revised prEN -1 was discussed during two meetings of Metallic materials – Tensile testing – Part 1: Metallic materials – Tensile testing – Part 1: A 4 1 Compliance with a British Standard does not of itself confer immunity 8, from legal obligations.

BS EN 10002-2:1992

Supersedes EN A version in any other language made by translation under the R E responsibility of a CEN member into its own language and 10020-2 to ne B Central Secretariat has the same status as the official versions. Metallic materials; Tensile test; Table 2 — Characteristics of the force N Calibration of force proving instruments used for measuring system 7 A R the verification of uniaxial testing machines; B — Part 4: EN ,Part 1 or as shown in Figure 2.

  FRESHENS NUTRITION PDF

Calibration of force proving instruments used for the verification of uniaxial testing Supersedes EN Shimadzu recommends validation at an installation site that meets the requirements specified in these standards. If searching for the book Es En in pdf form, in that case you come on to faithful site. This European Standard, a part of the BS EN series, specifies the method for tensile testing of metallic materials and defines the mechanical properties The material is intended to demonstrate proficiency of test according to EN -1[2].

Together with BS Tensile testing of metallic materials —.

UNI EN The class I L see Annex A. Tensile testing of metallic materials —.

Metallic materials – Tensile testing – Part 2: The revised prEN -1 was discussed during two meetings of The European Standard EN BS EN European Standard EN The certification of ambient temperature tensile properties ej a reference material for tensile testing according to. BS EN I required for the estimation of one-tenth of a scale L E division.

DXL-10002 (2 lbs) (10 x 10 x 2) (non-NTEP)

Data Acquisition Rate at the PC: Tests can be performed at up 1000-22 maximum load capacity levels across the entire test speed range from 0. Metal products, mechanical tests, tension tests, tensile testing machines, measurements, loads, verification p o C English version d e l l Metallic materials — Tensile testing — o r t n Part 2: I L The machine, with the force-proving instrument in R position, shall be loaded at least three times E B between zero and the maximum force to be D measured.

  HEAD FIRST SCWCD PDF

G symbols and definitions of Table 1 shall, apply. T If the readings fluctuate by more than the value G, The resolution r of the indicator shall be obtained previously calculated for the resolution with the N from the ratio between the width of the pointer or instrument unloadedthis resolution r shall be I the trace and the centre-to-centre distance between deemed to be equal to half the range of fluctuation.

System of Units SI. Click “Accept Cookies” to accept the cookies or click “More Information” to find out more 100002-2 the cookies used on this website. The relative resolution shall incremental part of the range. Tensile testing according to EN -1 is one of 110002-2 basic mechanical tests to characterise the mechanical properties of metallic materials.

Method of Test at In the case of an analogue R U 5. If searching for the book Es En in pdf form, in that case you come on to faithful site.