PDF Download


HT12E Encoder IC can be used only with its pair HT12D. These two ICs together form an Encoder and Decoder pair. Fri, 12 Oct GMT ht12e encoder ic ht12e datasheet pdf – HT12E is an encoder integrated circuit of. 2 12 series of encoders. They are. HT12E is a series encoder IC (Integrated Circuit) for remote control applications. It is commonly used for radio frequency (RF) applications. By using the.

Author: Kale Maunris
Country: Haiti
Language: English (Spanish)
Genre: Sex
Published (Last): 27 October 2007
Pages: 176
PDF File Size: 18.11 Mb
ePub File Size: 20.69 Mb
ISBN: 902-3-81079-846-6
Downloads: 19935
Price: Free* [*Free Regsitration Required]
Uploader: Goltikinos

It encodes the 12 bit eencoder data into serial for transmission through an RF transmitter. Choosing Battery for Robots. Supply voltage; 5V 2. The IC is has a wide range of operating voltage from 2.

We should set the bits in same pattern on Encoder and Decoder IC to pair them. HT12E begins a 4-word transmission cycle upon receipt of a transmission enable. It is very important that your Dncoder should also have this same address for them to talk to each other. Transmission enable; active low. These encofer bits are divided into 8 address bits and 4 data bits. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. The 4-bit data that has to be sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the dncoder A0 to A7. The Encoded 12 bit output data can be obtained from this pin. Skip to main content. Can range from 2.


HT12E Encoder IC

You can know to set up the HT12D after this from here. TL — Programmable Reference Voltage. These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits.

In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. The encoded bit can be obtained from the Dout pin pin Connected to the Ground of circuit.

HT12E Encoder IC Pin Diagram, Uses, Equivalents & Datasheet

In this image I have made all four data bits as zero lowhf12e this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC. This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR.

SPI Module of Arduino. Interface GPS with Arduino. They are paired with 2 12 series of decoders for use in dstasheet control system applications. The primary function of HT12E is to encode a bit and send it out through the output pin. This cycle is repeated as long as TE is kept low. The IC has a built in oscillator. These two ICs together form an Encoder and Decoder pair.

Submitted by admin on 30 October datashet Interface SD Card with Arduino. As soon as TE returns to high, the encoder output completes its final cycle and then htt12e. It is mainly used in interfacing RF and infrared circuits.


Arduino based GPS receiver.

So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. If you want security you can connect any of the 8 pins to 5V to make it high.

Choosing Motor For Robots. This oscillator can be used by connecting these two pins through a 1M Resistor. These are the 8-bit address bits, which is used to protect your data. Simply put, HT12E converts the parallel inputs into serial output. Virgin Galactic — Commercial Space Flight. For decoding a data the IC will requires an oscillator, luckily this IC has one in-built.

Pull the Transmission Enable pin pin 14 to ground to activate transmission. HT12E has a transmission enable pin which is active low. HT12E is an encoder integrated circuit of 2 12 series of encoders.

This high-density System-in-Package SiP integrates controller, power switches, and support components.

What is Web Browser. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. This pin has to be connected to Ground 0V to enable the Transmission. They can also be connected to switches to manually send and receive data.