PDF Download


And by using their ADC register we can interface. When we select microcontroller family for making any project, in which we need of an. Interface ADC with serial port (RS) using microcontroller ( AT89C51). This Project include circuit diagram and source code in C. Interfacing of ADC with microcontroller (AT89C51) project including circuit diagram and source code in C.

Author: JoJokora Arajar
Country: Martinique
Language: English (Spanish)
Genre: Health and Food
Published (Last): 1 August 2005
Pages: 232
PDF File Size: 8.17 Mb
ePub File Size: 8.71 Mb
ISBN: 805-5-63668-809-3
Downloads: 89201
Price: Free* [*Free Regsitration Required]
Uploader: Dakora

Interfacing ADC with Microcontroller: Tutorial with Circuit Diagram and Code

Step size is dac0804 change that can be measured by an ADC. I suggest T-junction with pendenstial sign traffic ligth with counter, heart beat rate,Dot matrix display all these with in assembly language.

Virgin Galactic — Commercial Space Flight. If you have any queries, doubts or feedback on this tutorial please share in our discussion forum.

Leave a Reply Cancel reply Your email address will not be published. For an ADC with resolution of 8 bits, the step size is Preset resistor R10 forms a voltage divider which can be used to apply a particular input analogue voltage to the ADC. After converting the analog data, the ADC stores the result in an internal register. A high to low pulse is sent to the RD pin to bring the converted data on the output pins.

In place of preset, analog input from a sensor can also be used. Previous post Next post. If INTR is low, go to next step else keep checking the status. And show on LCD as name Ch2. Send a low to high pulse to pin WR to start the conversion. This circuit demonstrates the principle and operation of collecting data from ADC and sending it to PC via serial communication using microcontroller AT89C I have not tested on the actual hardware but i have done the simulation in proteus and it works.


I am also including CS signal to give you a clear picture.

The IC Max is used to ensure compatibility between controller and serial port Refer serial port interfacing through controller. The figure above shows the schematic for interfacing ADC to While programming we will not use this signal.

Write WR pin 3 is connected to P2. Typical applications include sound processing, temperature processing etc.

If you want us to write tutorial for more devices please let us know in the forum. The program continuously monitors the output of ADC and transmits it to the serial port.

ADC can be given clock from external source. Keep this in mind that whenever you are working with an IC and you want to know how to communicate with that IC, then simply look into the timing diagram of that IC from its datasheet.

Keep monitoring the INTR pin. It also has an 8501 clock. AT89C51 is an 8-bit microcontroller and belongs to Atmel’s family. Below steps are for starting an ADC conversion.

In simple words P1 of the microcontroller is the input innterfacing and P0 is the output port.

For selecting all the other input channels, interfcing a look on the given table:. Interface GPS with Arduino. You may also like: Log in or register to post Comment.


How to interface ADC0804 using 8051 microcontroller (AT89C51)

The pin out diagram of ADC is shown in the figure below. Heart rate monitor with sms alert. For example, if the analogue input voltage Vin is 5V then all LEDs will glow indicating in binary which is the equivalent of in decimal.

There is a universal rule to find out how to use an IC.

Interfacing ADC with Microcontroller

Retrieved from ” http: A 9 volt battery and a 5 volt voltage regulator namely are used for powering the circuit. When we select microcontroller family for making any project, in which we need interfacibg an ADC conversion, then we use external ADC.

AT89s51 is the microcontroller used here. Choosing Motor For Robots.

These digital signals are used for further processing by the digital processors. And then ADC reads selected channel and send output to microcontroller. Below are the stepts to read output from inteerfacing ADC This is an active low output pin. In some application it is required to reduce the step size. This high-density System-in-Package SiP integrates controller, power switches, and support components.

An ADC has n bit resolution binary form where n can be 8,10,12,16 or even 24 bits. ADC gives ratio metric conversion output at its output pins.

If we give 5v to pin 9, will ADC work?