PDF Download

KSP 2222A DATASHEET PDF

KSP. A. NPN Epitaxial Silicon Transistor. Absolute Maximum Ratings Ta=25 °C unless otherwise . This datasheet contains the design specifications for. KSPA transistor is a general purpose transistor and hence fit into many applications, it is a direct substitute for 2NA transistor as both. KSPA Transistor Datasheet pdf, KSPA Equivalent. Parameters and Characteristics.

Author: Mooguzil Faulabar
Country: Djibouti
Language: English (Spanish)
Genre: Education
Published (Last): 22 June 2014
Pages: 121
PDF File Size: 19.55 Mb
ePub File Size: 15.55 Mb
ISBN: 767-1-30635-233-8
Downloads: 32868
Price: Free* [*Free Regsitration Required]
Uploader: Tor

KSPA 데이터시트(PDF) – Fairchild Semiconductor

Another Common application of a Transistor is as amplifiers. In this type of circuit, the Emitter and the Base pin of the transistor should be commonly connected to a same voltage, so we have connected it to the Ground potential using two resistors R4 and R3.

Every transistor has a gain h FE associated with it, which can be used to amplify voltage or current. However this type of amplifiers have many drawback and if you are looking for some serious datasheef applications then you should look into Op-Amps which are nothing but a package of many transistors put to gather with amplification as its sole purpose.

KSP2222A Datasheet

The capacitors C1 and C2 are simply used for filtering purpose. Again the values of the resistor mentioned above are only for reference commonly used you have kep design your own circuit based on the application and transistor you are using. Submitted by admin on 24 June KSPA is a NPN transistor hence the collector and emitter will be left open Reverse biased when the base pin is held at ground datasueet will be closed Forward biased when a signal is provided to base pin.

  ABUNDANCES OF KATHERINES PDF

When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region. It is very similar to a mechanical switch but here we will control the switch using electric signals. The resistor R2 is used to limit the current though the collector of the transistor and is not mandatory.

TL — Programmable Reference Voltage.

KSPA Transistor Pinout, Features, Equivalent & Datasheet

KSPA can allow collector current upto mA and also has power dissipation of mW which can be used to drive larger loads than compared with BC Applications General purpose NPN transistor Can be used to switch high current upto mA loads It can also be used in the various switching applications.

So if you looking for an NPN transistor that could switch loads of higher current then KSPA might the right choice for your project. The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor.

The transistor will begin to conduct when the voltage across the Base and Emitter pin exceeds 0. When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter.

  AHMED MARZOUKI CELLULE 10 PDF

Transistor as Amplifier Another Common application of a Transistor is as amplifiers.

Normally this type of transistor will either be used as a switch or as datasheett amplifier, both of which is discussed below. The base pin of the transistor has to be biased with a voltage; this voltage is provided by the potential divider network formed by the resistors R4 and R6.

One of the 222a2 default and primary function of a transistor is to act as a switch. There are many types of amplifier circuits that are possible with transistor but this is the most commonly used one because it is very good in amplifying low frequency voltage signals like audio signals.

The resistor R1 is called the Base resistor and is very important to drive a transistor, it limits the base current and failing to use one might damage the transistor permanently.

KSPA has a gain value of tothis value determines the amplification capacity of the transistor.

The vales of the Resistor in the above image are only for reference and are not accurate. But there are two important features that datahseet both.

To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA.